Short answer : A bed sheet holder is a simple accessory designed to keep fitted or flat sheets pulled taut against the mattress instead of bunching up overnight. Most versions work by clipping or gripping the sheet corners and edges, then anchoring them underneath the mattress with elastic straps, bands, or a fitted fastener system. This keeps the sleeping surface smooth, reduces the need to remake the bed each morning, and helps sheets stay in place for restless sleepers, adjustable beds, and deep mattresses where corners tend to pop off. Choosing a holder comes down to your mattress thickness, sheet type, and whether you prefer corner clips, a full elastic band, or a strap-based system that runs under the bed.
What a Bed Sheet Holder Actually Does
A bed sheet holder is a simple tensioning device that keeps a fitted or flat sheet pulled snug against the mattress instead of letting it ride up or bunch in the middle. Its job is not to change how a sheet feels or to add a layer of comfort—it is purely mechanical. The holder grips the fabric at the corners or along the edges and anchors it below the mattress, so the sheet stays flat while you move during the night. Most designs fall into a few broad categories: elastic straps that clip to the sheet corners and hook under the mattress, corner grips that pinch the fabric and tuck into the mattress edge, and garter-style bands that run diagonally underneath to pull opposite corners toward each other. Each works on the same principle of continuous, even tension.
The practical value shows up in the small annoyances that build over a night. A sheet that pulls loose at one corner creates a wrinkle that presses into your back, and a flat sheet that slides down leaves you tugging it back up before morning. A holder removes that repeated adjustment by keeping the fabric under mild tension from the moment you make the bed. The effect is most noticeable on deeper mattresses, where standard fitted sheets often struggle to reach fully under the corners, and on sheets that have lost some of their original elasticity after repeated washing. It also helps on adjustable beds and mattress toppers, where the added height makes a secure fit harder to achieve.
Different holders suit different situations. Corner clips and grips are the least visible option and work well when you mainly have a problem with one or two corners popping off. Elastic strap systems that connect diagonally underneath the mattress tend to hold more firmly across the whole surface, which makes them a better match for restless sleepers or for sheets that are slightly too large. Garter-style bands are quick to install and easy to move between beds, so they appeal to people who change linens often or want a solution they can take when traveling. The right choice depends on whether your issue is a single loose corner or a sheet that shifts across the entire mattress.
Installation is generally straightforward and takes only a few minutes: lift the corner of the mattress, attach the holder to the sheet, and route the strap or band underneath. Because the devices rely on tension rather than adhesive or hardware, they can be removed and repositioned without damaging the sheet. A few practical considerations matter when choosing one. Look for grips that hold fabric without leaving marks, straps with enough stretch to accommodate the depth of your mattress, and materials that will survive regular washing cycles. It is also worth checking that the holder is compatible with the type of sheet you use, since very thin or very thick fabrics can behave differently under tension. Used correctly, a holder keeps the bed looking neat and spares you the nightly routine of re-tucking.
Types of Bed Sheet Holders Compared
The most common bed sheet holder is the elastic corner strap, a short band that hooks under each corner of the mattress and grips the sheet corner above it. These are the simplest option and suit most beds, but their hold depends on a firm corner and a sheet with enough fabric to tuck. On deep mattresses or slippery sheets, a single corner strap can slide, so users often fit four at once. They are best for occasional lifting rather than a full retucking system.
The next step up is the adjustable corner clip with a strap running diagonally beneath the mattress. These connect two corners, pulling the sheet taut across the bed rather than just at the tips. Because the tension is adjustable, they handle thicker mattresses and looser sheets better than fixed elastic straps. The trade-off is fitting time: you lift the mattress and route the strap, which is more awkward on heavy beds but holds more reliably overnight.
For the strongest grip, there are full-length suspender-style systems that run under the mattress from head to foot and clip to the sheet edges at multiple points. These distribute tension across the whole sheet instead of concentrating it at the corners, which keeps the middle of the bed from rumpling. They suit restless sleepers and larger beds where corner-only holders tend to lose grip. Setup takes longer and the straps must be kept straight to avoid uneven pull.
A separate category covers flat sheets and duvet-style covers: clip-and-strap fasteners that grip the sheet edge and anchor to the mattress or bed frame. These are useful when the problem is a flat sheet riding up rather than a fitted sheet popping off a corner. They work well on guest beds and sofa beds where sheets are thinner and tuck less deeply, but they need an anchor point, so they are less suited to frameless or platform beds.
When choosing, weigh three things: how deep your mattress is, how slippery the sheet fabric, and how much setup effort you will tolerate. Corner straps are quick and cheap but weakest on deep or slick beds; diagonal and suspender systems hold better at the cost of fitting time; edge clips solve flat-sheet lift rather than corner pop. Match the holder to the specific failure you see, and a single type usually covers the whole bed.
Key Criteria for Choosing a Holder
Before you compare any two products, get clear on how the holder actually grips the sheet, because that single design choice determines whether it will work on your bed or fight you every morning. The most common approach uses a strap or band that runs underneath the mattress and clips or clamps to the corners, pulling the fitted sheet taut from below. These suit standard mattresses well and are easy to install once, but they can slip on very thick pillow-top mattresses or on smooth bases where the strap has little to bite against. Elastic corner grips, by contrast, hug each corner individually; they are quicker to fit and travel well, but they tend to hold less tension across the middle of the bed, so they shine on thinner mattresses and guest beds rather than deep, heavy ones.
Grip strength and surface compatibility matter more than most buyers expect. A clamp that bites firmly into fabric will hold a cotton or linen sheet securely, but the same clamp can leave marks or struggle on very silky, low-friction weaves, where a wider, flatter grip tends to perform better. Think about your sheet material and weave before choosing a mechanism: smooth sateen and bamboo blends reward broad contact surfaces, while crisp percale and flannel tolerate tighter, more concentrated clamps. If your sheets are delicate or expensive, favor a holder that spreads its hold over a larger area rather than pinching a small point.
Fit range is the next filter. Holders are built for a range of mattress depths and widths, and a strap sized for a slim mattress will either not reach around a deep one or will stretch so tight it distorts the sheet. Check the stated depth range against your actual mattress height, including any topper, and confirm the holder is adjustable rather than fixed-length. On split adjustable beds or unusually shaped mattresses, corner-only grips usually adapt more gracefully than a single continuous strap.
Durability and ease of use decide whether the holder survives daily life. Look for reinforced stitching at stress points, hardware that resists bending, and elastic that is described as heavy-duty rather than thin. Consider how often you wash your sheets: a holder you can leave attached to the mattress through several sheet changes saves real effort, while one that must be refitted from scratch each time quickly becomes a chore. Finally, weigh installation effort against your patience and mobility—straps that run under the mattress demand more lifting, whereas corner grips are far quicker to deploy.
Fabric and Sheet Compatibility Tips
Fabric choice determines whether a bed sheet holder grips securely or slides loose by morning. Smooth, tightly woven cotton and cotton-poly blends offer the most predictable surface: the fabric has little nap, so a clamp or strap can bite into the hem without tearing it. Flannel and brushed microfiber behave differently. Their raised fibers create grip for the holder but also make the sheet stretch and relax more under tension, so you often need to reseat the corners after the first night. If you use flannel seasonally, expect to adjust the holder more often than with percale or sateen, and check the hem for thinning where the grip sits.
Thread count and weave density matter as much as fiber type. A high thread count usually means a denser, heavier fabric that resists pulling through a clamp, while a loose weave or open knit can distort and leave a permanent stretched mark. Look at the hem seam: a double-stitched or reinforced corner hem holds a holder far better than a single thin seam, which can pull apart under steady tension. Deep-pocket sheets with elastic all around already hold themselves partly in place, so a holder mainly needs to stop corner creep rather than carry the full load.
Sheet thickness and pocket depth change the fit. Very thin sheets can slip out of a clamp unless the jaws have a textured or rubberized face; very thick or quilted mattress toppers paired with standard sheets leave little hem to grab, and the holder may need to sit further under the mattress edge. A practical test is to lift the corner of the fitted sheet and see how much fabric folds over the mattress: enough to clamp without stretching the seam is the target. If the hem barely reaches the underside, a holder that anchors under the mattress works better than one that clips only to the sheet.
Match the holder style to the bedding setup. Elastic corner straps suit standard fitted sheets on a single mattress and are easy to reposition when you change linens. Clamp-and-strap systems that run under the mattress hold better on thick mattresses and adjustable beds, where corner tension shifts as the frame moves. For split-top adjustable beds, separate holders on each side prevent one half from tugging the other. If you layer a mattress protector, fit the holder over the sheet but under the protector’s skirt so the protector does not lift the grip.
Care keeps compatibility stable over time. Wash sheets and holders separately, and check that clamp jaws are free of lint and fabric softener residue, which reduce friction and let the sheet slide. Rotate two sets of sheets so each has time to recover its shape, and inspect hems every few washes for fraying where the holder grips. A holder that suits your fabric and mattress depth will need only occasional adjustment; one that fights the fabric will loosen nightly no matter how tight you pull it.
How to Install Sheet Holders Correctly
Installing sheet holders correctly matters more than most people expect, because a holder that is clipped in the wrong place or under the wrong tension will either slip free by morning or pull the fabric into uncomfortable ridges. The goal is simple: anchor the sheet where it meets the mattress edge, with even tension across the whole perimeter, so the fitted corners stay put and the flat surface stays smooth.
Start by fitting the sheet onto the mattress as snugly as you can by hand, smoothing out wrinkles from the center toward each corner. A sheet that already sits flat needs far less correction from the holders. If your sheet has a fitted elastic band, tuck the excess fabric underneath the mattress before adding any clips, so the holder grips a single layer rather than a bunched wad of material. For flat sheets used as a bottom layer, fold the overhang into a neat triangular hospital corner first, then secure it.
Position each holder at the midpoint of a side or near a corner, pressing the fabric tight against the underside of the mattress before locking the clip or strap. Work around the bed in order rather than jumping from corner to corner, and apply roughly equal tension at each point. Uneven tension is the most common reason a sheet comes loose on one side while the rest stays firm. On a mattress with a deep profile, favor holders with longer straps or wider clips, since short elastic may not reach around the thickness; on a thin mattress, too much tension can bow the sheet inward, so ease off slightly.
The number of holders you use should match the bed size and how restless the sleeper is. A twin or full bed usually needs four to six points to stay secure, while a queen or king benefits from six to eight, especially along the long sides where sheets tend to creep. If you use corner-style grips, place them diagonally opposite each other first to establish balance, then fill in the remaining sides. For adjustable straps that connect two sides under the mattress, center the strap beneath the mattress so the pull is symmetrical.
Check the installation by pressing down on the sheet surface and running a hand along each edge. Any spot that lifts easily needs another holder or a tighter adjustment. After the first night, recheck the clips, since fabric settles and elastic relaxes slightly; a quick retensioning early on prevents the slow loosening that sends corners popping off later in the week. When changing sheets, release the holders before stripping the bed rather than pulling them off with the fabric, which preserves both the elastic and the sheet’s hem.
Cleaning and Maintaining Your Holders
Cleaning and maintaining your bed sheet holders is a simple routine, but the details depend on what the holder is made of. The two broad families are elasticized straps or bands, often wrapped in fabric or coated with silicone, and rigid clips or clamps that grip the sheet and anchor to the mattress or frame. Elastic fabric straps generally tolerate machine washing on a gentle cycle in a mesh laundry bag, while bare elastic and silicone grips last longer if washed by hand in lukewarm water with a mild detergent. Rigid clips should usually be wiped with a damp cloth rather than submerged, since moisture trapped in the hinge or spring mechanism encourages rust and weakens the grip. When in doubt, a quick hand wash is the safer choice for any holder with metal parts.
Frequency matters more than intensity. Sheets are typically changed weekly or every other week, and that is a natural moment to check the holders. Washing them every time you change the sheets is reasonable for fabric straps in direct contact with skin and mattress; rigid clips that sit mostly under the mattress edge can go several changes between cleanings. The practical signal to clean is tactile: when the grip starts feeling slick or the strap leaves a faint residue on the sheet, it is overdue. Perspiration, body oils, and lotion transfer to the elastic and reduce friction, which is exactly what these products rely on.
Drying is where many holders are quietly ruined. Heat is the enemy of elastic: a hot dryer cycle accelerates stretch loss and makes bands baggy, so air-drying flat or hanging is preferable, and a low-heat tumble only when necessary. Rigid clips should be dried immediately with a cloth, paying attention to springs and hinges, and left open to air fully before going back under the mattress. Storing holders bunched in a drawer under tension for months also takes a toll; loosely coiled is better than stretched around a bundle of other laundry.
Between washes, small habits extend life. Rotating two sets of holders spreads the wear, especially on corners that take the most pull. Checking the stitching where the elastic meets the clip or the fabric loop catches fraying early, before a strap fails mid-night. If a clip loses its bite, a gentle cleaning of the gripping surface often restores it more effectively than tightening anything. And if a holder is used on a mattress topper or a very smooth sheet, a quick wipe of the grip before each use keeps friction consistent.
Finally, know when to retire a holder. Elastic that stays stretched after release, fabric that has thinned to transparency, or a clip that no longer closes firmly are signs that cleaning cannot fix. Replacing a worn holder is cheaper than repeatedly remaking a bed, and keeping a spare set on hand means a failed strap never leaves you wrestling with a loose sheet at bedtime.
Common Mistakes That Cause Loose Sheets
Loose sheets rarely come down to a single dramatic failure; they usually result from a handful of small, repeated errors that compound over the course of a night. The most frequent culprit is buying bedding that doesn’t match the mattress dimensions. A deep-pocket sheet stretched over a standard-depth mattress leaves slack fabric that bunches and pulls free as soon as you move. The reverse is just as problematic: a shallow-pocket sheet forced onto a thick mattress or a mattress topper will pop off at the corners under tension, often within the first hour. Before blaming the sheet or the holder, confirm that the pocket depth comfortably covers the mattress plus any topper, with a little fabric left to tuck underneath.
Improper installation is the second major cause. Many people simply drop the sheet over the mattress and smooth it down, leaving the corners only partially anchored. A fitted sheet needs each corner pulled down firmly and seated fully under the mattress before the elastic is allowed to grip. If the elastic band is left riding on top of the corner rather than tucked beneath it, the sheet has almost nothing holding it in place. Taking an extra moment to lift each corner of the mattress and work the sheet underneath makes a noticeable difference in how long the bedding stays put.
Elastic fatigue is easy to overlook because it happens gradually. Over many washes and countless stretch-and-release cycles, the elastic around a fitted sheet loses its snap. A sheet that once gripped firmly may now feel slack the moment you pull it over the corner. If the elastic no longer snaps back when stretched, no amount of careful tucking will keep the sheet tight, and a bed sheet holder becomes a practical fix rather than an optional accessory. Rotating between two sets of sheets and washing them less aggressively helps preserve elasticity longer.
Movement during sleep is another factor people underestimate. Restless sleepers, couples sharing a bed, and anyone who sits or rolls near the edges put constant lateral force on the bedding. Sheets that are only held by corner elastic gradually creep toward the center of the mattress. This is where dedicated holders earn their place: they anchor the sheet across the middle and edges, not just at the corners, so the fabric resists sideways pull rather than relying on four small elastic bands.
Finally, mattress and bedding mismatches quietly undermine everything else. A smooth, low-friction mattress protector, a slippery mattress surface, or a sheet made from a smooth weave with little grip all encourage sliding. Layering too many loose items, such as a protector that isn’t fitted snugly, creates a shifting base beneath the sheet. Addressing these mismatches, combined with correct sizing and firm corner tucking, prevents most loose-sheet problems before a holder is even needed.
Budget Options Versus Premium Holders
When you start shopping for a bed sheet holder, the range of options can feel wider than it needs to be. Most products fall into two broad camps: inexpensive everyday holders and premium designs built with more substantial materials and adjustability. Understanding what separates them helps you spend wisely rather than simply buying the cheapest or the most expensive option on the shelf.
Budget holders typically rely on simple elastic straps, clips, or lightweight bands that hook under the mattress corners. They are inexpensive enough to buy several at once, which makes them a practical first purchase if you are unsure whether a holder will suit your sleeping habits. Their main trade-off is durability and grip strength: thin elastic can stretch out over time, and basic clips may slip on very smooth or deep mattresses. For a guest room, a rarely used bed, or a quick fix on a sheet that only occasionally comes loose, a budget holder often does the job well enough.
Premium holders generally use thicker elastic, wider straps, stronger clamps, or adjustable tension systems, and some designs distribute the pull across the whole sheet rather than just the corners. That extra material and engineering usually translates into a firmer, more consistent hold, which matters most on thick mattresses, adjustable beds, or for restless sleepers who move a lot. If you have already tried a cheap strap and found it snapped or lost its grip, stepping up to a sturdier design is often the more economical choice over repeatedly replacing flimsy ones.
The right choice depends on your bed and your habits. A standard mattress with a fitted sheet that stays mostly in place calls for nothing more than a basic holder. A deep mattress, a sheet that is slightly too large, or a household where sheets are changed and washed frequently points toward a more durable option that can withstand regular tension and laundering. Consider how often you will use it and how much tension the sheet actually needs before deciding.
A sensible approach is to start with an affordable holder to confirm the concept works for your bed, then invest in a premium version only if you notice slipping, stretching, or wear. Matching the holder to your mattress depth and sheet type matters more than the price tag itself, and a well-chosen budget option can outperform an ill-fitting premium one.
Holder Solutions for Adjustable Beds
Adjustable beds create a specific set of challenges for keeping sheets in place. When the head or foot section articulates upward, the mattress surface stretches and compresses unevenly, and a fitted sheet that stays put on a flat bed can suddenly pull loose at the corners or ride up along the hinge line. The result is a sheet that bunches under your back when the head raises, or snaps free at the foot when you lower the bed again. Standard corner grips designed for static mattresses often can’t accommodate this constant flexing, so it’s worth choosing holder solutions with the articulation in mind.
The most important criterion is elasticity with recovery. A holder that relies on rigid clips or fixed straps will fight the mattress movement rather than follow it, and repeated raising and lowering will gradually work the sheet loose. Look for stretch bands or elasticized straps that can extend and contract repeatedly without losing tension. Sheet straps that run corner-to-corner underneath the mattress tend to handle articulation better than short corner-only grips, because they keep tension distributed across the whole sheet rather than concentrating it at four points that move independently as the bed adjusts.
Placement matters as much as the holder type. On an adjustable base, the hinge zones—where the mattress bends—are where sheets loosen first, so a holder that anchors along the sides as well as the corners gives you more control over those flex points. If your sheet has deep pockets, a holder that pulls the fabric taut from underneath works well because it keeps the fitted corners seated even when the head section rises. For split adjustable beds, where two mattress halves move separately, each side needs its own independent holding setup; a single holder spanning both halves will pull against itself every time the two sides are at different angles.
Consider how often and how far you articulate the bed. If you mostly sleep flat and only raise the head occasionally, a simple set of elastic corner straps may be sufficient. If you keep the head elevated through the night or regularly adjust both head and foot sections, a more comprehensive strap system that runs under the mattress and grips along multiple edges will hold up better to constant movement. People who use the bed in a seated position for reading or watching television put the most stress on the foot and lower-back areas, so prioritize holders that keep those sections tight.
Finally, think about the mattress itself. Adjustable beds often pair with foam or hybrid mattresses that flex easily, and a heavy mattress can pull a lightweight sheet loose faster when it articulates. A holder with strong, wide elastic and secure fastening points will compensate for that weight and movement. Check that the straps are long enough to reach under a thicker mattress and that the fasteners won’t dig into the mattress surface as the bed bends. Matching the holder’s stretch and coverage to how your adjustable bed actually moves is the difference between sheets that stay smooth night after night and ones you’re re-tucking every morning.
When to Replace Your Sheet Holders
Sheet holders do wear out, and the signs usually appear gradually rather than all at once. The most reliable indicator is grip: if a holder that once held a corner firmly now slips loose within an hour or two of making the bed, the elastic or clamping mechanism has lost tension. A single slipping corner is often the first warning. When two or more corners release on the same night, the holder has typically reached the end of its useful life and replacement is the practical choice.
Stretched elastic is the second clear signal. Over months of nightly tension, elastic straps and bands relax, and a holder that used to pull sheets taut will start to feel slack the moment you stretch it over the mattress corner. A simple test is to compare the resistance when you install it with how it felt when new. If the strap stretches with little effort and does not snap back quickly, it will no longer keep sheets tight through the night. Fabric wear matters too: frayed stitching at the clip or strap junction, thinning elastic near the buckle, and small tears where the holder grips the sheet all shorten remaining life.
The bedding setup itself affects how long holders last. Thick mattress toppers, deep mattresses, and slippery sheet fabrics put more continuous strain on elastic and clips, so holders in these setups tend to wear faster than those on a standard mattress with cotton sheets. Frequent washing of the holders, especially in hot water or a dryer, accelerates elastic breakdown. If you rotate between two sets of holders, each set lasts longer, and you always have a spare on hand when one fails.
Use patterns also matter. A guest bed used occasionally may keep its holders in good condition for a long time, while a bed that is made and remade daily, or one used by a restless sleeper who pulls at the sheets, will wear holders out sooner. Households that wash bedding weekly put more cycles on the holders than those that change sheets less often. If you notice yourself re-tucking the same corner every morning, that is a practical cue to inspect the holder rather than assume the sheet is the problem.
Finally, consider safety and fit. Any holder with a cracked plastic clip, a bent metal clamp, or exposed elastic core should be retired, since these defects reduce grip and can snag or tear sheets. Holders that no longer match the mattress depth, such as after upgrading to a deeper mattress, will strain constantly and fail early. Keeping a simple replacement rhythm, replacing holders when grip fades or elastic slackens rather than waiting for a corner to pop loose mid-night, keeps the bed looking neat and saves the frustration of constant re-tucking.
Frequently asked questions
What is a bed sheet holder used for?
A bed sheet holder is a clip, strap, or elastic band system that grips the edges of a fitted or flat sheet and anchors them underneath the mattress. Its job is to keep the sheet pulled taut so corners stay in place instead of popping off during the night. People use them on fitted sheets that have lost elasticity, on flat sheets used as bottom sheets, and on any bed where the sheet tends to bunch up or slide loose with movement.
Do sheet holders work on deep pocket sheets?
Yes, most sheet holders are designed with deep pocket sheets in mind, since those are the sheets most likely to slip off thick mattresses. Straps and corner clips with adjustable elastic can reach across the extra fabric and grip the underside of the mattress. The key is choosing a holder with enough strap length or stretch to span the mattress depth, and pulling the excess fabric flat before fastening so the sheet sits smooth rather than bunched.
Will sheet holders damage my mattress?
Sheet holders generally do not damage a mattress when used as intended. Clips grip the sheet fabric, not the mattress surface, and straps run underneath the mattress where there is no contact with the sleeping surface. Risk comes from overtightening, which can compress the mattress edge or stress the sheet fabric, and from sharp or rusty metal parts. Smooth, rounded clips and moderate tension keep both the sheet and the mattress in good condition.
Are sheet holders safe for silk sheets?
Silk sheets need gentler handling because the fabric is delicate and prone to snags and creases. Smooth-edged clips without sharp teeth, or wide elastic bands that spread pressure over a larger area, are the safer choice. Avoid metal jaw clips with aggressive teeth, which can pull threads. Fasten loosely enough that the silk is held flat without heavy stretching, and check the clip edges for roughness before each use to prevent snags.
How many holders do I need per bed?
The number depends on the holder style. Corner clip sets typically use one holder per corner, so four for a standard bed. Strap systems often use two straps that run corner to corner underneath the mattress, or a combination of corner grips and side straps. For a sheet that slips badly, adding side holders along the long edges gives extra grip. Start with corner coverage and add more only where the sheet still pulls loose.
Can sheet holders be used on sofa covers?
Yes, sheet holders are commonly repurposed for sofa covers, slipcovers, and chair covers that shift with use. Corner clips and elastic straps can tuck excess fabric under cushions or around frame edges to hold the cover taut. The approach works best on removable covers with enough fabric to grip. Very thick upholstery or covers without loose edges may need different fastening, but standard elastic holders handle most slipcover jobs.
Do sheet holders work with mattress toppers?
They can, but the setup needs care because a topper adds thickness and its own tendency to shift. Fit the topper first, then the sheet over it, and run the holder straps under the mattress rather than just around the topper. Straps that span the full mattress depth hold both layers better. If the topper slides independently, a separate topper strap or a textured topper base reduces movement before the sheet holder is added.
How do I stop sheets from slipping nightly?
Start with a clean, dry mattress surface and a sheet that fits the mattress depth, since oversized sheets bunch and undersized ones pop off. Smooth the sheet flat before fastening holders at the corners, and add side grips where slipping recurs. Rotating two sheet sets reduces elastic wear, and washing fitted sheets in cool water and air-drying preserves their stretch. A mattress protector with a textured underside also reduces sliding beneath the sheet.
Put it into practice : How do I keep pet hair off my duvet cover?
